Vespel Flat Washer, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 1)

Vespel Flat Washer, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 1) Reviews

Other Picture

Vespel Flat Washer, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 1) Feature

• Flat Washers are an economical choice
• Vespel is suitable where high temperature, high strength, and low levels of outgassing are desirable
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Vespel is a high performance polyimide material, which can operate continuously from cryogenic temperatures to 550 degrees Fahrenheit, with excursions to 900 degrees Fahrenheit. Vespel parts exhibit superior performance in a variety of applications requiring low wear and long life in severe environments. Vespel, unlike most plastics, is non-flammable. Parts perform without melting or softening, and resist radiation sterilization more effectively than most other plastics. Vespel parts exhibit a very low level of outgassing, even in high vacuum environments, and are chemically compatible with most fuels, solvents, lubricants and hydraulic fluids. Vespel has above average tensile strength for a polymer, at 12,600 psi (pounds per square inch). Vespel will absorb 0.24% of its weight when exposed to water for 24 hours. Vespel is extremely impact resistant, rated at 14 foot pounds (on the Izod Impact Scale), which compares favorably against Nylon 6/6 at 3 foot pounds. Vespel also has excellent insulating properties, measured in terms of dielectric strength, with a rating of 260 volts/millimeter.

Visit Store Now !!

Detail Products

Detail Reviews

Sep 22, 2011 08:38:04

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100)

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100) Reviews

Other Picture

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Stainless Steel is suitable where formability and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.

Visit Store Now !!

Detail Products

• Stainless Steel Hex Nut, 1/4"-20 (Pack of 100)
• Stainless Steel 18-8 Split Lock Washer, ANSI, 5/16", 0.317" ID, 0.583" OD, 0.078" Thick (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, 3/8"-16, 1-1/2" Length (Pack of 25)
• Zinc Plated Steel Hex Nut, #2-56 (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)

Detail Reviews

Aug 18, 2011 03:45:04

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5)

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5) Reviews

Other Picture

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Great for homeowner repairs, general MRO applications

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These standard (thin) Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Sanyo Eneloop 8 Pack AA NiMH Pre-Charged Rechargeable Batteries

Detail Reviews

Aug 13, 2011 06:29:04

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.750" OD, 0.094" Thick (Pack of 10)

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.750" OD, 0.094" Thick (Pack of 10) Reviews

Other Picture

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.750" OD, 0.094" Thick (Pack of 10) Feature

• Component Flat Washers are manufactured with thicker materials for extra strength and load distribution properties
• The most popular sizes of extra strength steel washers in a corrosion resistant stainless steel
• 18-8 Stainless Steel is a good looking (bright and shiny) material with good surface finish and corrosion resistance
• Used anywhere a thick, strong, and corrosion resistant good looking washer is required
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. 18-8 Stainless Steel material offers excellent corrosion resistance, are harder than Brass, exhibit a slight magnetism, and are an attractive silver color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Stainless Steel 316 Hex Bolt, 3/8"-16, 2" Length (Pack of 5)

Detail Reviews

Aug 05, 2011 00:12:04

Structural Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.813" OD, 0.125" Thick (Pack of 10)

Structural Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.813" OD, 0.125" Thick (Pack of 10) Reviews

Other Picture

Structural Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.813" OD, 0.125" Thick (Pack of 10) Feature

• These flat washers are manufactured to the SAE Inner and Outer Diameters, but have more than double the thickness for better strength and performance
• This is a double thick SAE Pattern Washer for extra strength manufactured from corrosion resistant Stainless Steel
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Used anywhere a strong and corrosion resistant washer is needed
• Made In USA for excellent quality conformance

Structural washers are based on the standard SAE pattern (Society of Automotive Engineers) inner and outer diameters, but manufactured up to twice as thick as the standard SAE for extra strength. Offered from stock in bolt sizes 1/4" through 1", and thicknesses range from 3/32" through 5/16". 100% Made in the USA from DFARS compliant material, and both stamped and turned depending on size and manufacturing levels. Used anywhere an extra thick and extra strength washer is needed, coupled with corrosion resistance. 300 series Stainless Steel offers a good combination of strength and corrosion resistance.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 02, 2011 12:56:07

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 5)

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 5) Reviews

Other Picture

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 5) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Great for homeowner repairs, general MRO applications

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These standard (thin) Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Sanyo Eneloop 8 Pack AA NiMH Pre-Charged Rechargeable Batteries

Detail Reviews

Jul 24, 2011 03:13:03

Extra-Thick Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.406" ID, 1.000" OD, 0.188" Thick (Pack of 10)

Extra-Thick Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.406" ID, 1.000" OD, 0.188" Thick (Pack of 10) Reviews

Other Picture

Extra-Thick Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.406" ID, 1.000" OD, 0.188" Thick (Pack of 10) Feature

• Component Flat Washers are manufactured with thicker materials for extra strength and load distribution properties
• Extra Thick for extra strength and load distribution properties
• Low Carbon Steel, Case Hardened, and Black Oxide Plated
• General industrial, mechanical, machinery, power transmission uses
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. Low Carbon Steel is case hardened for extra surface hardness, while retaining the flexibility of a soft inner core, and then black oxide plated for an attractive finish.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

Jul 21, 2011 20:27:06

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 10)

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 10) Reviews

Other Picture

Fender Flat Washer, 316 Stainless Steel, Round Shape, Plain Finish, USA Made, 3/8" Bolt Size, 0.406" ID, 1.625" OD, 0.056-0.070" Thick (Pack of 10) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• 316 Stainless Steel offers more corrosion resistance over the standard 18-8 grades
• Great for exposure to salt water, chemical rich environments

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These standard (thin) Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Stainless Steel 316 Machine Screw, Flat Head, Phillips Drive, #6-32, 1-1/4" Length (Pack of 25)
• Stainless Steel 316 Machine Screw, Pan Head, Phillips Drive, 1/4"-20, 3/4" Length (Pack of 25)
• Stainless Steel Sheet Metal Screw, Hex Head, Self-Drilling Point, #10-16, 3/4" Length (Pack of 100)
• 3 Pc. Power Extension Socket Adaptor for Drills

Detail Reviews

Jul 06, 2011 23:45:04

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.875" OD, 0.125" Thick (Pack of 10)

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.875" OD, 0.125" Thick (Pack of 10) Reviews

Other Picture

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 0.875" OD, 0.125" Thick (Pack of 10) Feature

• An extra thick flat washer that comes in steel, 18-8 and 316 Stainless, and Brass
• A stamped flatwasher originally used in the tool and die industry, and now used for its' extra thick design which has superior load distribution properties
• Brass is a soft material that offers excellent corrosion resistance, especially in marine environments, and are not magnetic
• Used for general MRO and industrial applications - excellent for marine environments
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. Brass material offers excellent corrosion resistance, are non magnetic, soft, and are an attractive gold color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Advanced Tool Design Model ATD-359 110 Piece Copper Washer Assortment
• Dremel 512E EZ Lock Fine Grit Finishing Abrasive Buffs, 2-Pack

Detail Reviews

Jun 27, 2011 20:26:04

Nylon 6/6 Flat Washer, 3/8", 0.406" ID, 0.984" OD, 0.125" Thick (Pack of 100)

Nylon 6/6 Flat Washer, 3/8", 0.406" ID, 0.984" OD, 0.125" Thick (Pack of 100) Reviews

Other Picture

Nylon 6/6 Flat Washer, 3/8", 0.406" ID, 0.984" OD, 0.125" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M3-0.5, 10mm Length (Pack of 100)
• Nylon 6/6 Hex Nut, 1/4"-20 (Pack of 100)
• Nylon 6/6 Shoulder Washer, 0.120" ID, 0.154" OD, 0.062" Thick, 0.291" Shoulder Diameter, 0.296" Length (Pack of 100)
• 5mm Metric Flat Washer (100 count)
• Nylon 6/6 Threaded Rod, 1/4"-20, 36" Overall Length (Pack of 1)

Detail Reviews

Jun 14, 2011 06:24:08

Fiberglass Flat Washer, ANSI, 3/8", 0.406" ID, 1" OD, 0.063" Thick (Pack of 10)

Fiberglass Flat Washer, ANSI, 3/8", 0.406" ID, 1" OD, 0.063" Thick (Pack of 10) Reviews

Other Picture

Fiberglass Flat Washer, ANSI, 3/8", 0.406" ID, 1" OD, 0.063" Thick (Pack of 10) Feature

• Washers distribute load on a fastener
• Fiberglass is suitable for applications where tensile strength to weight, non-conductivity and corrosion resistance are all important considerations
• Size Name corresponds to matching screw or bolt size

Washers are generally round plates with a hole, designed to distribute the load on a threaded fastener. They can also be used as spacers or to reduce vibration.

Nonconductive and resistant to many corrosives, Fiberglass is a good choice for applications threatened by salt water, oils, mild solvents, and other harsh environments. G-10 is a glass reinforced fiberglass, utilizing a continuous woven glass fabric laminated with an epoxy resin. The glass reinforcing increases tensile strength over non-reinforced fiberglass, G-10 in particular is rated at 38,000 psi (pounds per square inch range). G-10 exhibits a high tensile strength to weight ratio, approximately twice that of Aluminum 2024, for example. G-10 is very non-porous, and will only absorb 0.1% of water if left to soak for 24 hours. G-10 is flame retardant and will operate at temperatures up to 280 degrees without degrading. This material is recommended for applications where superior strength and excellent electrical insulative properties are required over a wide range of temperatures.

Visit Store Now !!

Detail Products

• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
• Nylon 6/6 Shoulder Washer, #10, 0.201" ID, 0.437" OD, 0.06" Thick (Pack of 100)
• Stainless Steel Machine Screw, Flat Head, Slotted Drive, #0-80, 1/4" Length (Pack of 100)
• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, #6-32, 1/2" Length (Pack of 100)
• Stainless Steel Machine Screw, Binding Head, Slotted Drive, #12-24, 1/2" Length (Pack of 100)

Detail Reviews

Jun 05, 2011 04:25:06

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.000" OD, 0.125" Thick (Pack of 10)

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.000" OD, 0.125" Thick (Pack of 10) Reviews

Other Picture

Component Flat Washer, Brass, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.000" OD, 0.125" Thick (Pack of 10) Feature

• An extra thick flat washer that comes in steel, 18-8 and 316 Stainless, and Brass
• A stamped flatwasher originally used in the tool and die industry, and now used for its' extra thick design which has superior load distribution properties
• Brass is a soft material that offers excellent corrosion resistance, especially in marine environments, and are not magnetic
• Used for general MRO and industrial applications - excellent for marine environments
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. Brass material offers excellent corrosion resistance, are non magnetic, soft, and are an attractive gold color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

Jun 01, 2011 12:51:03

Extra-Thick Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.406" ID, 2.000" OD, 0.125" Thick (Pack of 5)

Extra-Thick Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.406" ID, 2.000" OD, 0.125" Thick (Pack of 5) Reviews

Other Picture

Extra-Thick Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.406" ID, 2.000" OD, 0.125" Thick (Pack of 5) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area, and the extra thickness of these washers provide extra strength as well
• A stamped product from low carbon steel, soft, and zinc plated for corrosion resistance
• A versatile washer used anywhere that a large bearing surface and thickness are needed
• Made In USA for excellent quality conformance

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These extra thick Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel. The increased thickness provides superior strength, as the thicker the washer, the stronger it gets.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

May 18, 2011 19:39:04