Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.531" ID, 1.500" OD, 0.219" Thick (Pack of 5)

Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.531" ID, 1.500" OD, 0.219" Thick (Pack of 5) Reviews

Other Picture

Component Flat Washer, Steel, Black Oxide, Round Shape, USA Made, 0.531" ID, 1.500" OD, 0.219" Thick (Pack of 5) Feature

• Component Flat Washers are manufactured with thicker materials for extra strength and load distribution properties
• Extra Thick for extra strength and load distribution properties
• Low Carbon Steel, Case Hardened, and Black Oxide Plated
• General industrial, mechanical, machinery, power transmission uses
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. Low Carbon Steel is case hardened for extra surface hardness, while retaining the flexibility of a soft inner core, and then black oxide plated for an attractive finish.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Black Oxide Heat Treated Alloy Steel Socket Head Cap Screw, Hex Socket Drive, 3/8"-24, 3/4" Length (Pack of 100)

Detail Reviews

Oct 09, 2011 01:14:44

Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.281" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 50)

Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.281" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 50) Reviews

Other Picture

Fender Flat Washer, Low Carbon Steel, Zinc Plated, Round Shape, USA Made, 0.281" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 50) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• Low Carbon Steel has a protective Zinc Plating for corrosion resistance - RoHs compliant
• Excellent multi purpose washer for general applications
• Made In USA for excellent quality conformance

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These extra thick Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel. The increased thickness provides superior strength, as the thicker the washer, the stronger it gets.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, #10-24, 3/8" Length (Pack of 100)
• Zinc Plated Steel Sheet Metal Screw, Pan Head, Phillips Drive, #10-16, 1/2" Length (Pack of 100)
• Zinc Plated Steel Hex Nut, 5/16"-18 (Pack of 100)
• Mirka 23-615-AP 5-Inch 8-Hole Assorted Grits (10 Each Of 80/100/120/150/220) Dustless Hook-and-Loop Sanding Disks
• 3M 8210Plus Particulate Respirator N95, 20-Pack

Detail Reviews

Sep 04, 2011 21:17:04

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5)

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5) Reviews

Other Picture

Fender Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 3/8" Bolt Size, 0.406" ID, 1.500" OD, 0.052-0.072" Thick (Pack of 5) Feature

• Fender Flat Washers have extra large outside diameters in relation to their bolt size
• Extra large Outside Diameter spreads the load over a wider area
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Great for homeowner repairs, general MRO applications

Fender Flatwashers were named because of their original use in auto body repair. The large outer diameter covered up a lot of area, and also spread the load across a wide area of thin sheet metal. In todays world these washers are used in electrical, construction, HVAC, and general industrial applications. The purpose of a washer is to spread the load from the head of the bolt across a wider area than the bolt head, which increases the strength of the joint. Fender washers do this well because the outer diameter is so much larger than the diameter of a standard flat washer. These standard (thin) Fender washers are manufactured in Steel Zinc, 18-8 Stainless Steel, and Type 316 Stainless Steel.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Sanyo Eneloop 8 Pack AA NiMH Pre-Charged Rechargeable Batteries

Detail Reviews

Aug 13, 2011 06:29:04

Machined Flat Washer with Beveled Outside Edge, Soft Steel, Plain Finish, Round Shape, USA Made, 0.781" ID, 1.500" OD, 0.250" Thick (Pack of 5)

Machined Flat Washer with Beveled Outside Edge, Soft Steel, Plain Finish, Round Shape, USA Made, 0.781" ID, 1.500" OD, 0.250" Thick (Pack of 5) Reviews

Other Picture

Machined Flat Washer with Beveled Outside Edge, Soft Steel, Plain Finish, Round Shape, USA Made, 0.781" ID, 1.500" OD, 0.250" Thick (Pack of 5) Feature

• Beveled Flat Washers are machined on Lathes, and feature a large bevel or chamfer on the top side
• Originally called "Williams Washers" the large beveled edge on the top of the washer assists operators in assembling products in mass quantities
• 12L14 Low Carbon Steel is machined, and then left soft and plain
• Used in many general industrial applications where corrosion resistance is not needed
• Made In USA for excellent quality conformance

Beveled Flat Washers (also known as "Williams Washers") are turned from solid bar, and feature a large bevel or chamfer on the top outside edge. Originally manufactured for the dual purpose of protecting assemblers from the sharp edges that are possible with a stamped washer, and also to allow them to orient the washer quickly, these washers have gained popularity for other purposes. Used in construction and architectural applications as an interesting visual part of the design, they offer the strength that is provided by their thickness. A small inner diameter provides a tight fit to bolts, rods, and studs, and eliminates most shifting and vibration of the washer. General industrial, marine, power transmission, and agricultural uses are popular.

Manufactured on Lathes from 12L14 Low Carbon Steel, this washer is left soft and plain. Useful for welding this washer to other components, or using it in another manufacturing process. 100% USA made. Available from #10 through 1-1/4" Bolt Size.

Visit Store Now !!

Detail Products

Detail Reviews

Jun 22, 2011 09:24:03

Roughneck Flat Washer, Case Hardened Steel, Plain Finish, Round Shape, USA Made, 0.844" ID, 1.500" OD, 0.250" Thick (Pack of 10)

Roughneck Flat Washer, Case Hardened Steel, Plain Finish, Round Shape, USA Made, 0.844" ID, 1.500" OD, 0.250" Thick (Pack of 10) Reviews

Other Picture

Roughneck Flat Washer, Case Hardened Steel, Plain Finish, Round Shape, USA Made, 0.844" ID, 1.500" OD, 0.250" Thick (Pack of 10) Feature

• Roughneck flat washers are extra thick, strong washers. No finish gives these a rough appearance.
• Case Hardened Steel washers without a finish accept a weld
• Low Carbon Steel, Case Hardened and plain
• Used in applications that require a large, tough washer, where corrosion is not a problem
• Made In USA for excellent quality conformance

Roughneck washers are 4 sizes of extra thick flat washers, with a large tolerance inner diameter. Useful where an extra thick washer is needed, and corrosion resisistance is necessary. Offered in a limited range from 3/8" Bolt Size to 3/4" Bolt size. Stamped or Turned depending on our manufacturing loads, and 100% Made in the USA. Low Carbon Steel is case hardened, but left plain without any plating. Washers have a mottled brown appearance from the heat treat process, and are not corrosion resistant at all.

Visit Store Now !!

Detail Products

Detail Reviews

May 17, 2011 03:57:04