PVDF Flat Washer, #6, 0.141" ID, 0.281" OD, 0.031" Thick (Pack of 5)

PVDF Flat Washer, #6, 0.141" ID, 0.281" OD, 0.031" Thick (Pack of 5) Reviews

Other Picture

PVDF Flat Washer, #6, 0.141" ID, 0.281" OD, 0.031" Thick (Pack of 5) Feature

• Flat Washers are an economical choice
• PVDF is suitable for applications that require high purity and low water absorption, along with greater strength than PTFE
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Polyvinylidene Fluoride, or PVDF, has a useful temperature range of -148 to 300 degrees Fahrenheit. PVDF exhibits similar properties to Kynar, a trade name of the Arkema Corporation. PVDF is generally used in applications requiring high purity, strength, and resistance to solvents, acids, bases and heat. It also generates little smoke during a fire event. PVDF exhibits below average strength as compared to Nylon 6/6, with tensile strength ranging from 5000 to 7000 psi (pounds per square inch) and impact strength of 1.2 foot pounds (on the Izod Impact Scale) as compared to 9000 psi, and 3 foot pounds, respectively. PVDF is stronger than PTFE and could be desirable where PTFE is not strong enough for the application. PVDF will absorb little or no water after 24 hours of exposure (less than 0.05% of weight impact). PVDF also has below average dielectric strength of 260 volts per millimeter (compared to 500 volts/mm for Nylon).

Visit Store Now !!

Detail Products

Detail Reviews

Aug 31, 2011 00:01:05

Nylon 6/6 Flat Washer, ANSI, #8, 0.188" ID, 0.625" OD, 0.062" Thick (Pack of 100)

Nylon 6/6 Flat Washer, ANSI, #8, 0.188" ID, 0.625" OD, 0.062" Thick (Pack of 100) Reviews

Other Picture

Nylon 6/6 Flat Washer, ANSI, #8, 0.188" ID, 0.625" OD, 0.062" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Visit Store Now !!

Detail Products

• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 10mm Length (Pack of 100)
• Nylon 6/6 Shoulder Washer, 0.256" ID, 0.290" OD, 0.031" Thick, 0.348" Shoulder Diameter, 0.093" Length (Pack of 100)
• Nylon 6/6 Hex Bolt, #10-32, 1/4" Length (Pack of 50)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 7/8" Length (Pack of 100)

Detail Reviews

Aug 30, 2011 04:41:04

Component Flat Washer, Brass, Round Shape, USA Made, #0 Bolt Size, 0.063" ID, 0.125" OD, 0.019" Thick (Pack of 25)

Component Flat Washer, Brass, Round Shape, USA Made, #0 Bolt Size, 0.063" ID, 0.125" OD, 0.019" Thick (Pack of 25) Reviews

Other Picture

Component Flat Washer, Brass, Round Shape, USA Made, #0 Bolt Size, 0.063" ID, 0.125" OD, 0.019" Thick (Pack of 25) Feature

• An extra thick flat washer that comes in steel, 18-8 and 316 Stainless, and Brass
• A stamped flatwasher originally used in the tool and die industry, and now used for its' extra thick design which has superior load distribution properties
• Brass is a soft material that offers excellent corrosion resistance, especially in marine environments, and are not magnetic
• Used for general MRO and industrial applications - excellent for marine environments
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. Brass material offers excellent corrosion resistance, are non magnetic, soft, and are an attractive gold color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Brass C260 Seamless Round Tubing, 3/8" OD,0.317"ID, 0.029" Wall, 12" Length
• Advanced Tool Design Model ATD-359 110 Piece Copper Washer Assortment
• Dremel 512E EZ Lock Fine Grit Finishing Abrasive Buffs, 2-Pack
• SE Pick Set, 12Pc
• SE Diamond Wheel Set 6PC DW13 1/8" Shank

Detail Reviews

Aug 29, 2011 00:56:04

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, #2 Bolt Size, 0.094" ID, 0.188" OD, 0.028" Thick (Pack of 25)

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, #2 Bolt Size, 0.094" ID, 0.188" OD, 0.028" Thick (Pack of 25) Reviews

Other Picture

Component Flat Washer, 18-8 Stainless Steel, Round Shape, USA Made, #2 Bolt Size, 0.094" ID, 0.188" OD, 0.028" Thick (Pack of 25) Feature

• Component Flat Washers are manufactured with thicker materials for extra strength and load distribution properties
• The most popular sizes of extra strength steel washers in a corrosion resistant stainless steel
• 18-8 Stainless Steel is a good looking (bright and shiny) material with good surface finish and corrosion resistance
• Used anywhere a thick, strong, and corrosion resistant good looking washer is required
• Made In USA for excellent quality conformance

Component Flat Washers are named for their original popularity as a component of a jig or fixture, where a thicker washer was needed for the extra strength and load distribution properties that accompany the extra thickness. Our Component Washers are available from #4 screw size all the way thru 1-1/2" Bolt sizes. All Component Washers are thicker than any standard washer in general use. We provide two lines from stock - Thick and Extra Thick. Smaller diameters have a 5/64" thickness, going all the way up to 3/8" thickness, with the 1/8" thick line being the most popular. These washers are either stamped on power presses or turned on our lathes depending on the quantities we manufacture, and the wall thickness of the washer, which is the relationship between the thickness and the Inner Diameter dimension. All of these are suitable for use anywhere extra strength is needed. 18-8 Stainless Steel material offers excellent corrosion resistance, are harder than Brass, exhibit a slight magnetism, and are an attractive silver color.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

• Stainless Steel 316 Hex Bolt, 1/4"-20, 1-3/4" Length (Pack of 25)

Detail Reviews

Aug 28, 2011 00:28:04

Shoulder-Lengthening Shim Washer for Shoulder Screws, 18-8 Stainless Steel, Round Shape, USA Made, Fits 1/4" Shoulder and #10 Thread Diameter, 0.171" ID, 0.241" OD, 0.016" Thick (Pack of 50)

Shoulder-Lengthening Shim Washer for Shoulder Screws, 18-8 Stainless Steel, Round Shape, USA Made, Fits 1/4" Shoulder and #10 Thread Diameter, 0.171" ID, 0.241" OD, 0.016" Thick (Pack of 50) Reviews

Other Picture

Shoulder-Lengthening Shim Washer for Shoulder Screws, 18-8 Stainless Steel, Round Shape, USA Made, Fits 1/4" Shoulder and #10 Thread Diameter, 0.171" ID, 0.241" OD, 0.016" Thick (Pack of 50) Feature

• These Shim Washers are designed to be used on the threaded end of a Stripper or Shoulder Bolt to make the shoulder length extend further
• These Shims are manufactured in 3 different thicknesses to make up any dimension
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Used to alter either shoulder or thread lengths on Stainless Steel Shoulder Bolts
• Made In USA for excellent quality conformance

These Shim Washers are designed to work with Socket Head Shoulder Bolts (also knowm as Stripper Bolts) to alter the length of the shoulder portion. Manufactured with the same outside diameter as the Shoulder Bolt shoulder, when added over the threads of the bolt, they serve to lengthen the shoulder portion of the bolt, while decreasing the threaded length. Available for Shoulder Bolts from 1/4" through 5/8" Shoulder diameters. For applications that require odd length shoulders to be used as pivot points or bearing surfaces, these Shim Lengthening Washers are great. Manufactured in the USA of 300 series stainless steel, Stamped and Burr Free.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 26, 2011 21:33:13

Spherical Flat Washer, Complete Set, Case Hardened Steel, Black Oxide, Round Shape, USA Made, 1.063" ID, 2.000" OD, 0.330" Thick (Pack of 1)

Spherical Flat Washer, Complete Set, Case Hardened Steel, Black Oxide, Round Shape, USA Made, 1.063" ID, 2.000" OD, 0.330" Thick (Pack of 1) Reviews

Other Picture

Spherical Flat Washer, Complete Set, Case Hardened Steel, Black Oxide, Round Shape, USA Made, 1.063" ID, 2.000" OD, 0.330" Thick (Pack of 1) Feature

• A male and female mating set that is self adjusting to align slightly mismatched components
• Male and Female halves are machined for a matched set
• Low Carbon Steel, Case Hardened, Black Oxide Plated
• Machinery, MRO, Power Generation, Transportation, Leveling
• Made In USA for excellent quality conformance

Spherical Washer Sets allow the top and bottom halves to adjust to compensate for uneven or mismatched surfaces, achieving a flat bolting surface. A set consists of a female half (concave) where the washer is hollowed out or curved inward, while the male portion is convex (bulging outwards). These two halves match for a perfect set. The thickness of the set is calculated by putting both halves together and measuring the overall thickness. Both halves are machined and turned on our machines from 12L14 Low Carbon Steel. Parts are then case hardened, which hardens only the top layer of steel, leaving the center soft - this imparts strength on the bearing surface, but allows the part itself to flex, and avoid cracking from being too brittle. A Black Oxide plating is then applied, for appearance and a corrosion inhibitor. Made in the USA.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 25, 2011 15:32:03

Stainless Steel 18-8 Flat Washer, ANSI, 1/2", 0.531" ID, 1.75" OD, 0.1" Thick (Pack of 100)

Stainless Steel 18-8 Flat Washer, ANSI, 1/2", 0.531" ID, 1.75" OD, 0.1" Thick (Pack of 100) Reviews

Other Picture

Stainless Steel 18-8 Flat Washer, ANSI, 1/2", 0.531" ID, 1.75" OD, 0.1" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Stainless Steel is suitable where formability and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.

Visit Store Now !!

Detail Products

• Stainless Steel Hex Nut, 1/4"-20 (Pack of 100)
• Stainless Steel 18-8 Split Lock Washer, ANSI, 5/16", 0.317" ID, 0.583" OD, 0.078" Thick (Pack of 100)
• Zinc Plated Steel Hex Nut, #2-56 (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, #8-32, 5/8" Length (Pack of 100)

Detail Reviews

Aug 24, 2011 19:18:13

Nylon 6/6 Flat Washer, 5/16", 0.34" ID, 0.875" OD, 0.125" Thick (Pack of 100)

Nylon 6/6 Flat Washer, 5/16", 0.34" ID, 0.875" OD, 0.125" Thick (Pack of 100) Reviews

Other Picture

Nylon 6/6 Flat Washer, 5/16", 0.34" ID, 0.875" OD, 0.125" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Nylon 6/6 is suitable where non-conductivity, corrosion resistance, and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Nylon 6/6 is a general purpose thermoplastic with outstanding resistance to organic chemicals, acids and alkalis. Nylon wears well against other surfaces; it is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications which should be taken into account with its use. Tensile strength of this material is 12,000 psi (pounds per square inch).

Visit Store Now !!

Detail Products

• Zinc Plated Steel Machine Screw, Pan Head, Phillips Drive, M5-0.8, 10mm Length (Pack of 100)
• Nylon 6/6 Hex Nut, #4-40 (Pack of 100)
• Nylon 6/6 Shoulder Washer, 0.200" ID, 0.281" OD, 0.050" Thick, 0.422" Shoulder Diameter, 0.21" Length (Pack of 100)
• Nylon 6/6 Hex Bolt, #10-32, 1/4" Length (Pack of 50)
• Nylon 6/6 Machine Screw, Binding Head, Slotted Drive, #4-40, 7/8" Length (Pack of 100)

Detail Reviews

Aug 23, 2011 20:36:04

Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 9/16" ID, 1-1/4" OD, 0.062" Thick (Pack of 50)

Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 9/16" ID, 1-1/4" OD, 0.062" Thick (Pack of 50) Reviews

Other Picture

Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 9/16" ID, 1-1/4" OD, 0.062" Thick (Pack of 50) Feature

• Commercial standard flat washer for general industrial or MRO applications where corrosion resistance is needed
• Standard washer for use where corrosion resistance is desired
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Used for general MRO and industrial applications needing corrosion resistance
• Made In USA for excellent quality conformance

A standard general purpose flat washer manufactured in both 18-8 and Type 316 Stainless Steels, entirely in the USA of DFARS compoant steels. Available from stock in bolt sizes #4 all the way up to 1-1/2". Manufactured from standard gage thicknesses, these washers are good for general industrial, MRO, and anywhere extra strength is not needed.

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 21, 2011 16:03:04

Jumbo Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 1-1/2" Bolt Size, 1.625" ID, 3.000" OD, 0.125" Thick (Pack of 1)

Jumbo Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 1-1/2" Bolt Size, 1.625" ID, 3.000" OD, 0.125" Thick (Pack of 1) Reviews

Other Picture

Jumbo Flat Washer, 18-8 Stainless Steel, Plain Finish, Round Shape, USA Made, 1-1/2" Bolt Size, 1.625" ID, 3.000" OD, 0.125" Thick (Pack of 1) Feature

• Jumbo Washers are designed for extra large bolting up to 4" diameter
• A machined washer that is extra big, extra strong, and extra fine
• 303/304 Stainless Steel has excellent corrosion resistance
• Construction, Power generation, Machinery, Transportation
• Made In USA for excellent quality conformance

Jumbo Flat Washers are designed for large bolts - available from stock in both a 4140 Alloy Steel and 18-8 Stainless Steel from 1-3/8" Bolt Szie all the way up to 4" Bolts. Inner Diameter is manufactured 1/8" larger than the bolt to allow for slight alignment issues, and to accomodate a thicker hot dip galvanized bolt shank. Extra large outer diameters and thickness up to 5/16" provide extra bearing surface and extra strength. 4140 Alloy Steels are fully through hardened to Rockwell C40-C50, and finished with a Black Oxide plating. This provides a suitable washer for Grade 5 or Grade 8 bolts, and some Structural Bolting applications. 100% Made in USA, with DFARS compliant raw materials. (Certification available at extra cost, and on special order only). 300 Series Stainless Steels are also DFARS compliant (Certification also available at extra cost, and for special orders only).

Visit Store Now !!

Detail Products

Detail Reviews

Aug 20, 2011 20:56:07

Non-Metallic Flat Washer, Fiberglass, Round Shape, USA Made, 1" Bolt Size, 1.015" ID, 1.755" OD, 0.093" Thick (Pack of 20)

Non-Metallic Flat Washer, Fiberglass, Round Shape, USA Made, 1" Bolt Size, 1.015" ID, 1.755" OD, 0.093" Thick (Pack of 20) Reviews

Other Picture

Non-Metallic Flat Washer, Fiberglass, Round Shape, USA Made, 1" Bolt Size, 1.015" ID, 1.755" OD, 0.093" Thick (Pack of 20) Feature

• Insulating Washers of Fiberglass protect components from heat and electricity, and are chemically resistant
• These washers are thicker compared to their outer diameter than usual, for greater strength and insulation
• Polyster Glass Laminates (Fiberglass) come in light tan and green colors
• This Fiberglass material meets General Purpose NEMA (National Electrical Manufacturers Association) GPO-1 Standards
• Made In USA for excellent quality conformance

Fiberglass washers are insulators of both thermal and electrical energy. They are chemically resistant, and have a high strength to weight ratio. This series is available from stock in sizes from numbe 2 thru 1" bolt sizes. Larger sizes have an oversized outside diameter, which protects and insulates.

Polyster Glass Laminates (Fiberglass) come in light tan and green colors, this material meets General Purpose NEMA (National Electrical Manufacturers Association) GPO-1 Standards.Temperatures up to aprox 200 degress are not a problem for this material

Made in the USA. These flat washers are produced in the USA for excellent quality conformance. One of the significant differences between less expensive imported products and ours are the way we stamp. Many cheap imports are produced on gang dies that produce 10 or more washers per stroke of the press. Using such a large die means that the individual washer sets are not adjustable - when the punch wears, the dimensions change and there is no way to fix this as the press produces washers, leading to a large variation in the finished part.

Materials available in many other countries are not as consistent as the domestic steels we use, which gives the imports a cheaper cost, but can lead to failures and inconsistencies when the products are used. The Defense Federal Acquisition Regulation Supplement (DFARS) was created to address this problem. Our materials are DFARS compliant although we do not supply the certification except on special order.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 19, 2011 06:33:04

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100)

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100) Reviews

Other Picture

Stainless Steel 18-8 Flat Washer, ANSI, #10, 0.203" ID, 0.406" OD, 0.04" Thick (Pack of 100) Feature

• Flat Washers are an economical choice
• Stainless Steel is suitable where formability and cost are important considerations
• Size Name corresponds to matching screw or bolt size

Standard flat washers are an economical choice when your application calls for spacers, shims, or re-enforcements with nominal dimensions only.

Stainless steels are used for their corrosion resistance, high-temperature strength, scaling resistance, and low-temperature toughness.  These properties account for their extremely wide use in practically every industry. Austenitic Stainless Steels are alloys of iron and carbon that contain between 16% and 30% Chromium, a maximum of 0.15% carbon, along with Nickel (or Manganese), and other alloying elements.  The chromium, which helps develop a passive surface oxide film, provides corrosion resistance in stainless steels.   Austenitic Stainless Steels are designated by a 3 digit SAE Stainless Steel Grade beginning with the number 3 (e.g. 304, 316).  Another common naming convention for Austenitic Stainless Steels are 18/8, 18/10, 18/0, etc. where the 18 refers to the % of Chromium and 8 to the % of Nickel contained in the material.

Visit Store Now !!

Detail Products

• Stainless Steel Hex Nut, 1/4"-20 (Pack of 100)
• Stainless Steel 18-8 Split Lock Washer, ANSI, 5/16", 0.317" ID, 0.583" OD, 0.078" Thick (Pack of 100)
• Stainless Steel Machine Screw, Pan Head, Phillips Drive, 3/8"-16, 1-1/2" Length (Pack of 25)
• Zinc Plated Steel Hex Nut, #2-56 (Pack of 100)
• Nylon Flat Washer, DIN, M5, 5.30mm ID, 11.00mm OD, 1mm Thick (Pack of 100)

Detail Reviews

Aug 18, 2011 03:45:04

Precision Shim Flat Washer for Bearing Inner Race Spacing, 18-8 Stainless Steel, Round Shape, USA Made, 0.125"-0.130" ID, 0.182"-0.192" OD, 0.012" Thick (Pack of 25)

Precision Shim Flat Washer for Bearing Inner Race Spacing, 18-8 Stainless Steel, Round Shape, USA Made, 0.125"-0.130" ID, 0.182"-0.192" OD, 0.012" Thick (Pack of 25) Reviews

Other Picture

Precision Shim Flat Washer for Bearing Inner Race Spacing, 18-8 Stainless Steel, Round Shape, USA Made, 0.125"-0.130" ID, 0.182"-0.192" OD, 0.012" Thick (Pack of 25) Feature

• Shim washers are manufactured with extremely tight thickness tolerances so they can be used to make up an exact dimension
• Designed to fit over precision shafts and protect the Inner Race of a Bearing
• 18-8 Stainless Steel is the most common corrosion resistant Stainless Steel used in Flat Washers
• Precision machinery, technical instrumentation, prototypes, model makers, power transmission
• Made In USA for excellent quality conformance

These Shim Washers are also known as Bearing Inner Race Spacers, and Precision Shaft Spacing Shim Washers. A comprehensive line offering thicknesses from 0.001" up to 0.016" from stock. Shaft sizes covered are 5/64", 3/32", 1/8", 3/16", 1/4", 5/16", 3/8", and 1/2". Manufactured from full hard 300 series stainless for strength and corrosion resistance. 100% made in the USA of DFARS compliant steel.

Used originally to go between the inner race of a bearing and the shaft support, they have evolved into a tight tolerance precision shim used in electronics, industrial, and power transmission applications. Precision stamped, and burr free.

Visit Store Now !!

Detail Products

Detail Reviews

Aug 16, 2011 03:43:04